Home > AR-15 Parts >

AR15 / AR10 Reduced Power Hammer Spring - 2 PACK

AR15 Mil-Spec Reduced Hammer Spring - 2PK


 
Alternative Views:


This hammer spring is all you need to replace in order to lighten (reduce the weight) of your AR15 / AR10 trigger giving you a cleaner trigger pull for increased accuracy. It can be installed in a matter of minutes and works on all GI, Mil-Spec triggers both single and double stage. If you have a trigger in your AR that is not a complete drop-in solution, you need this spring. Use it in conjunction with our adjustment grip screw for an even better trigger using your stock AR15 or AR10 trigger parts.

Application: The Reduced Power Hammer Spring is intended for competition and recreational use only and should not be installed in any rifle used for defense or duty applications. By reducing the spring tension, the introduction of light strikes or failures to fire due to the lack of primer detonation may occur.

International Orders Click HERE

MSRP: $11.95
Our Price: $8.95
Savings: $3.00

Shipping: Usually Ships in 1 to 2 Business Days
Part #: AR15-HAMMER-SPRING-2PK
Qty:

Installation Instructions RESTRICTIONS
 
All you need is a punch or hex wrench small enough in diameter to push out the hammer pin located in your AR15 lower. Once you push out the hammer pin, the hammer and spring can be removed from the lower. Take note of the orientation of the spring as it sits on the hammer so that you can install the new spring in the same position. Simply pull the spring off the hammer by grabbing one of the coils and pull. Install the Reduced Power Spring onto the hammer and reinsert the hammer/spring into the lower while pushing the hammer pin back into place through the lower. Be careful not to force the pin as you attempt to push it through the lower. Remember the lower is aluminum and the pin is steel, so forcibly hitting the pin or pushing harshly it may cause damage to your lower if all is not lined up perfectly.
AR15 Reduced Power Hammer Spring Install Instructions

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 6 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Reduced power hammer springs! May 24, 2021
Reviewer: Mr. Snow  
The reduced power hammer springs prevent broken firing pins! I use these reduced power springs in all of my 3D printed recievers using AR fire controls. MacDaddy, DB9, and Hoffman Tactical lowers. Youtube.com/c/mrsnowmakes

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Quality Product At A great Price May 19, 2021
Reviewer: Anonymous Person from Tucson, AZ United States  
Installing reduced power hammer and trigger springs (along with polishing of all 3 trigger group parts) reduced trigger pull from 7  1/2# to 4#.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 December 2, 2020
Reviewer: Wyatt O. from Harlan, IA United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Great springs October 27, 2020
Reviewer: cesar from baldwin park, CA United States  
These do the job,  I normally buy Anderson or Aero lower parts kits and adding this spring the FCG really makes a difference.  I’ve purchased the grip screw as well and both together really make average triggers work a lot better.  I’ve used them on my 556 and 300 blackout builds.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Reduced Power Hammer Spring August 15, 2020
Reviewer: Greekcop50 from Hanford, CA United States  
Awesome product, will purchase again and fast shipping

Was this review helpful to you?

View All Customer Reviews