Home > Springs >

Smith & Wesson M&P22 Replacement Recoil Spring

M&P22 Recoil Spring | S&W M&P22 | Smith & Wesson | M&P-22 | M&P22 | Walther | Replacement recoil Spring | nictaylor00 upgrade | 22lrupgrades | recoil spring | replacement spring


 
Alternative Views:


Having feeding issues? Replace your worn out recoil spring and improve performance. This recoil spring is a direct replacement part for your Smith & Wesson M&P-22 long rifle pistol. Keep in mind this is a new spring and therefore it has not yet "set" or been compressed yet. So the first time you install it may seem too long but it is the correct length and will become shorter after being compressed. See the installation instructions for a tip to install new recoil springs in Walther type 22LR pistols.

International Orders Click HERE

MSRP: $8.95
Our Price: $5.25
Savings: $3.70

Shipping: Usually Ships in 1 to 2 Business Days
Part #: 101-0FRS-MP22
Qty:

Installation Instructions RESTRICTIONS
 
1) Activate the takedown lever.

2) pull back the slide all the way to the rear and pull up the back side of the slide.

3) While holding the rear section of the slide up allow the side to move forward and come off the frame.

4) Remove the old recoil spring.

5) Install the new recoil spring and reverse steps 1-4. Using a rod the diameter of the internal diameter of the spring will aid in guiding the spring onto the guide rod while assembling the gun. (See the photos below).

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 8 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 order April 30, 2021
Reviewer: Robert Duby from Ocala, FL United States  
order was filled in good time and was what I wanted

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Tricky to install longer factory spring April 21, 2021
Reviewer: michael mitchell from starkville, MS United States  
My worn out spring was 3 inches shorter than when new. This makes it a challenge to install.
I found that you’ll need 2 small flat head screwdrivers. You’ll use screwdriver one to pull the spring coils down on the rod, in a motion like you were using flat tip to scrape the rod.
Then use other screwdriver to pull more spring on. Alternate until entire spring is cat walked on the rod and then install slide. Wear eye pro!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Must have March 18, 2021
Reviewer: Anonymous Person from Traverse City, MI United States  
Works perfectly and solved the binding issue with my slide.
Pro-Tip:  BEFORE install, slide spring over a #2 pencil and fully compress by hand numerous times to "resize" spring and make proper installation easier. Otherwise you chance buggering up the spring trying to set it over the guide rod.

excellent product!
Shipped quickly.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Great upgraded spring December 31, 2020
Reviewer: Paul j Conforti from www.ainsmallinstruction.com  
M&p 22 was having some problem cycling.  It was a little finicky with some of the 22s.  I decided to buy a new recall spring and found this one online.  took a little bit of work to get the recoil spring inside the frame and it's longer than the standard spring. once I got the gun off closed up though you could feel the difference in the slide closing.  I ran an entire magazine of the ammunition didn't want to run and it ran perfectly.  I'm glad I bought two springs.  If anybody else has any p-22 should buy one of these springs and replace the stock spring

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 October 16, 2020
Reviewer: Topdog from Effingham, IL United States  
Ordered new recoil springs for my M&P ... got just what I needed Quick...

Was this review helpful to you?

View All Customer Reviews