Home > AR-15 Parts >

AR15 / AR10 Skeletonized Trigger

AR15 low cost trigger job | Flat AR trigger | Mil-Spec | AR-15 | trigger job | drop in


 
Alternative Views:


Skeletonized flat trigger for AR type rifles and variants. The Bullmoose flat trigger is a drop in replacement trigger that works with milspec fire control components and is designed to lighten your trigger pull for a precision rifle feel at a fraction of the cost. The flat trigger surface provides an even and consistent trigger pull where ever the operators finger is placed. 4.5-5.5lb trigger pull with milspec springs. Use in conjunction with the included NicTaylor00 reduced powder hammer and trigger springs for an even lighter trigger pull (sold HERE). Both trigger and spring can be installed in a matter of minutes. Finish off your new trigger with a "Speed Hammer" to eliminate the light primer strikes when using light weight springs. You can find the Bull Moose Speed Hammer HERE

*THERE MAY BE RESET ISSUES WITH SOME HAMMERS.


Application: The Reduced Power Hammer Spring is intended for competition and recreational use only and should not be installed in any rifle used for defense or duty applications. By reducing the spring tension, the introduction of light strikes or failures to fire due to the lack of primer detonation may occur.

International Orders Click HERE

MSRP: $29.99
Our Price: $26.99
Savings: $3.00

Shipping: Usually Ships in 1 to 2 Business Days
Part #: MSR-BMT-TRIGGER
Qty:

Installation Instructions RESTRICTIONS
 
All you need is a punch or hex wrench small enough in diameter to push out the hammer and trigger pins located in your AR15 lower. Once you push out the hammer pin, the hammer and spring can be removed from the lower. Take note of the orientation of the spring as it sits on the hammer so that you can install the new spring in the same position. Simply pull the spring off the hammer by grabbing one of the coils and pull. Install the NicTaylor00 Reduced Power Hammer Spring onto the hammer and set it aside.

Remove the selector by loosening or removing the grip screw. This will lessen the tension on the selector detent spring and allow the selector to be removed. Push out the trigger pin and lift out the trigger and trigger spring from the lower. Take note of the trigger spring and install the NicTaylor00 Reduced Power Trigger Spring onto the Bull Moose Tactical Skeletonized trigger in the same orientation. Reinsert the trigger / spring and disconnector into the lower and install the trigger pin. Next reinsert the selector making sure the detent is in place, then tighten the grip screw.

Reinsert the hammer/spring into the lower while pushing the hammer pin back into place through the lower. Be careful not to force the pin as you attempt to push it through the lower. Remember the lower is aluminum and the pin is steel, so forcibly hitting the pin or pushing harshly it may cause damage to your lower if all is not lined up perfectly.
Bull Moose Skeletonized Flat Trigger

Average Rating: Average Rating: 5 of 5 5 of 5 Total Reviews: 36 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Excellent product for the price. November 13, 2021
Reviewer: Anonymous Person from Lewisville, TX United States  
I wasn't aware that you could find a flat face trigger at this price. Wanted a heavier trigger over my CMC and this was the perfect option given the price. Instillation was easy and the trigger pull weight was what I wanted.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 November 11, 2021
Reviewer: Randy Moore from LAKELAND, FL United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Flat Trigger & Anti Walk Pins October 20, 2021
Reviewer: Aaron Short from London, KY United States  
Great Skeletonized trigger, great Anti walk pins. I only have a couple issues. The Flat rigger contact surfaces need cleaned up and lightly polished, and came with no trigger grease, and the anti walk pins need slight surface polish, to keep the hammer and trigger from riding them, and cam with no lok tight agent, but with the Taylor Tactical reduced spring trigger Kit, I purchased at an earlier time, I have ended up with an awesome mil-spec flat trigger with a great pull and I mean great pull. with very little effort, cost way less then any flat drop in trigger that I saw, I recommend all the item I have Purchased at Taylor Tactical good prices fast shipping just good all together I recommend Taylor Tactical Supply and the item they sell, all in all I am very happy with my purchases

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 September 21, 2021
Reviewer: Ricky Roberts from Morenci, MI United States  


Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Only Reasonably Priced Straight Trigger September 9, 2021
Reviewer: from , ARIZONA  
Well manufactured, served the purpose of a Straight trigger with a short pull. Well manufactured, probably should be 49.99 but still the cheapest option out there....

Was this review helpful to you?

View All Customer Reviews