Home > Springs >

Smith & Wesson M&P22 Reduced Power Recoil Spring

M&P22 Recoil Spring | S&W M&P22 | Smith & Wesson | M&P-22 | M&P22 | Walther | Replacement recoil Spring | nictaylor00 upgrade | 22lrupgrades | recoil spring | replacement spring


 
Alternative Views:
Having issues cycling low power "bulk" 22 ammo? Using a reduced power recoil spring may help alleviate the problem. The factory recoil spring in the Smith & Wesson M&P-22 is approximately 4 pounds. Our reduced power recoil spring is approximately 3.3 pounds. The reduction in spring weight may help your pistol cycle lower power ammo for more reliable function. The ammo has to overcome the tension of the recoil and striker/hammer springs in the gun. Reducing the tension on the springs may help with reliability. There is no guarantee that changing to a lighter recoil spring will solve the problem 100% since the ammo still has to over come the spring tension of the striker/hammer spring. But this is a low cost, simple method that may work for your gun and ammo. NOT FOR THE M&P15-22

Keep in mind this is a new spring and therefore it has not yet "set" or been compressed yet. So the first time you install it may seem too long but it is the correct length and will become shorter after being compressed. See the installation instructions for a tip to install new recoil springs in Walther type 22LR pistols.

International Orders Click HERE
MSRP: $8.95
Our Price: $5.25
Savings: $3.70


Shipping: Usually Ships in 1 to 2 Business Days
Part #: 101-RPRS-MP22
Qty:

Installation Instructions RESTRICTIONS
 
1) Activate the takedown lever.

2) pull back the slide all the way to the rear and pull up the back side of the slide.

3) While holding the rear section of the slide up allow the side to move forward and come off the frame.

4) Remove the old recoil spring.

5) Install the new recoil spring and reverse steps 1-4. Using a rod the diameter of the internal diameter of the spring will aid in guiding the spring onto the guide rod while assembling the gun. (See the photos below).

Average Rating: Average Rating: 3.5 of 5 3.5 of 5 Total Reviews: 10 Write a review »

  0 of 0 people found the following review helpful:
 
5 of 5 Got this to go w/ Captured Guide Rod Assembly.. December 28, 2023
Reviewer: Anonymous Person  
Haven't tried this yet, but want to match it up w/ the Captured Guide Rod Assembly.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Smith & Wesson M&P22 Reduced Power Recoil Spring July 20, 2023
Reviewer: Michael Smith from Pahrump, NV United States  
Ammunition that would not cycle now cycles. Than

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Good alternative to regular power springs July 13, 2023
Reviewer: PAULP from Poop streets of(LA), CA United States  
Work great, though some examples of mp22 even need these to be trimmed, but not by much. Will continue to buy these alongside regular springs.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 Five stars April 14, 2022
Reviewer: Frank Martin from Hamilton, NJ United States  
Excellent service and great product!

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
5 of 5 M&P 22 (w/ Silencer) mods to cycle CCI Quiet 22 October 21, 2021
Reviewer: Anonymous Person from Orange, VA United States  
Installed the spring. First round- casing ejected and chamber closed but did not chamber next round. This is an improvement from previously not completely ejecting spent casing.
Second round- same result as first.
Third round- after ejecting mag and racking spring. Two rounds fired In rapid succession. Then failed to chamber third round. This is a success but will likely need some tweaking and is a positive result. After only 4 rounds!

Was this review helpful to you?

View All Customer Reviews